What sort of desktop computer should I get for EMAN2 reconstructions

People frequently ask what sort of computer they should get for EMAN2 (or other image processing work). This isn't a page for the "minimum required specifications", but a page of recommendations for a high end workstation for data processing. EMAN2 will run even on a fairly basic 4 core laptop. The tutorials are designed so they can run on most typical laptop computers. However, if you are doing a typical single particle reconstruction project with 300,000 particles and a 300x300x300 reconstruction, you aren't going to be using a laptop. The better the computer you buy the faster your work will go. You could process even a large data set on a typical desktop computer _eventually_, but this could easily take 10-50x longer than on a proper workstation, and 100-1000x longer than on a Linux cluster. Expect to spend $3-5k for a minimal effective data processing workstation, and if you plan to do a lot of work in the field, I would suggest getting a proper ~$5-15k workstation with a lot of RAM, many cores, at least one good Nvidia GPU and a lot of high performance storage.

(Almost) Timeless Recommendations

Since I won't always update this page every few months, let me give a few general tips:

• In 2017, AMD started to produce competitive processors again. Our initial benchmarks show that they perform extremely well, and may be considerably more cost-effective than Intel's offerings. Ryzen/Threadripper/Epyc all seem to perform quite well, clock for clock against intel.
• For the sort of processing we typically do, scaling is basically linear with CPU speed, and almost linear with number of cores. So, when pricing, optimize the product of these two numbers. In other words, maximize cores*speed/total cost.
• There are still some tasks that do NOT scale with number of cores, so if the product of speed * cores is similar, opt for the machine with fewer faster cores.
• Try for at least ~4 GB/core of RAM, with an absolute minimum of 2 GB/core. This is particularly true if you plan to use other image processing software as well. For high resolution subtomogram averaging, you
• Get an NVidia GPU. EMAN2 uses these for only a limited number of tasks, but other software you may wish to use with EMAN2 does use them heavily. It probably isn't worth the extra $$$ for one of the very high-end Tesla cards. The highest end consumer card is usually the best choice. In some cases RAM may be an issue, so the Titan series may be worth the extra $ in some case.
• Get a big monitor with high resolution, or multiple monitors. Small 4K TVs are quite cheap now, and you really want the extra resolution for working with large images and other purposes.

Storage:

• Disk performance is critical for many tasks. There are 2 ways to get high speed disk access:
  • SSD -
    • A good M.2 SSD can provide 10 - 20x the performance of an individual spinning platter drive. HOWEVER - they are not as reliable, and capacities are much lower. These are great for the operating system, and possibly 'working storage' while processing, but probably not for long-term archival.
    • SATA SSDs are similar to M.2 except they are much slower, limited by the speed of the SATA interface. If you have a choice, M.2 is the better option.
    • DANGER - SSDs are not designed for long-term shelf storage! If you unplug a SSD and put it on a shelf, or power off the PC and put it in a closet, SSDs will eventually (years typically) start to lose data. Spinning platters will not. Do NOT use SSD's for long term data archival!
  • RAID of traditional hard drives
    • Each spinning platter hard drive will provide ~150 MB/s, which is quite slow compared to SSDs. However, when you build a RAID array the drive performance adds. An 8 drive RAID 5 array with a hardware RAID controller can easily provide 1 GB/s read/write speeds, and also offers the redundancy of RAID 5 with the better capacity and long term reliability of spinning platters.

    • Supermicro is known for making nice workstation cases which support arrays of 8 hot-swap SATA drives. With 16 TB drives now available for ~$500 you could add over 100 TB of RAID 5 storage to a workstation for <$5k and have >1GB/s performance. This is an excellent solution for general data processing and long term archival.

• Regardless of how you store your data, DON'T FORGET THE NEED for BACKUPS. Even if you build a RAID array, failures happen!

Update mid pandemic (2020)

64 Core AMD Threadrippers are now available, and are a great option if you can afford one.

The 3000 series NVidia RTX graphics cards are a great option (particularly the 3090) if you can find them in-stock. At present you can only get them in the secondary market

If you are using the new subtomogram averaging pipeline heavily, make sure you get enough RAM. For a 64 core machine, 256 GB of ram is generally a good idea (this meshes with the general advice above

Update mid 2019

The new(ish) AMD Ryzen ThreadRipper 2990WX has 32 cores running at an unboosted 3 GHz. I have one and it is an excellent choice for CryoEM image processing. Equivalent in performance to an equal number of Intel cores, but substantially cheaper. Other AMD chips are also good. I'm using it with a Gigabyte X399 DESIGNARE EX, which aside from needing a bios update, has been doing well.

Make sure you get enough RAM. With 32 cores, target at least 64 GB of RAM, and if you plan to do serious tomography, at least 128 GB.

Hard drive advice hasn't really changed, though larger drives are now readily available.

Update mid 2017

For about $10k. Not promoting a specific manufacturer, but I speced this Workform 3000.v6 at Silicon Mechanics:

• 2x Intel Xeon E5-2690v4, 2.6GHz (14-Core each)
• 128 GB RAM
• 8x hard drives with a RAID controller. Size the drives based on your needs. RAID is critical to get speed. SSDs are great for speed but you may want more capacity.
• 2x GPU, suggest Nvidia 1080Ti. Higher end Tesla cards are perhaps 2x faster and have more RAM, but may cost 5-10x more.

Update late 2014

Earlier this year I updated my workstation to get something for <$10k that would be optimal for processing movies as well as single particle reconstruction for small-medium projects. We have purchased a couple of machines like this, and they are quite cost effective and perform very well. Here are the basic specs:

• Case with 8 hot-swap drives : Supermicro SC743 TQ-865B-SQ - tower - 4U
• SUPERMICRO X9DAE Motherboard
• 2x Intel Xeon E5-2650v2 (8 core, 2.6 - 3.4 Ghz)
• 128 GB DDR3 RAM
• 8x 4TB WD Black drives
• PCIe RAID controller with cables - LSI MegaRAID SAS 9271-8i Kit

This was earlier in the year, so there are probably better processor choices now, but this machine performs very well. Disk performance is ~1.2 - 1.5 GB/sec with ~24 TB of storage. 16 cores (32 threads) with threading which actually works (~30% speed boost over using 16 threads). Total cost (self-assembled) was ~$8000. Some of the prices will have fallen since then.

Of course this is just representative, and you can likely get a vendor to build you one for about the same price.

Update late 2013

In the Intel lineup today, for a basic machine (<$2000), I would probably lean towards a single 6-core, i7-3930K Sandy Bridge-E 3.2GHz (3.8GHz Turbo). If you want to go all-out, a machine with dual 8-core Xeon (E5-2690 Sandy Bridge-EP 2.90GHz) processors is currently at the high-end of the lineup, but this will run you about $4000 just for the two CPUs, so you could easily hit $5000-7000 for a machine like this with a decent amount of RAM. My normal RAM recommendations haven't changed much 2G/core is enough for most applications, but if you want to do tomography or deal with large viruses at high resolution, you may want 64+ GB (regardless of the number of cores). RAM is cheap enough that 64 GB isn't all that expensive.

For many projects, you can get away with relatively little in modern computer terms. My quad-core mac laptop, for example, can refine a ribosome to ~12 Å resolution overnight very easily. It's when you start pushing for higher resolutions or larger structures that the computing needs really increase, and in such situations you are probably better off getting some time on a cluster, instead of paying $10k for a super-duper workstation. My recommendation would be to get a high clock speed single CPU computer with 4 or 6 cores for desktop use.

SSD hard drives are (each) ~4x faster than traditional spinning drives. They have improved dramatically in recent years (as shown by their use in all current Mac laptops). They are still expensive, but much less so than they used to be. Many tasks in cryo-EM data processing, particularly with DDD movie data, are disk-limited, so you can improve the interactivity of your computer dramatically by at least supplementing your regular hard-drives with SSDs.

Two options for SSD use:

• single 256 or 512GB SSD drive used for booting.
  • make SURE that NO swap space is allocated on the SSD. SSD's have limited lifetimes, and SWAP involves a lot of reading/writing. IMHO, there is no need for any swap at all on a computer with 16+GB of RAM, and not much reason to get a machine with less RAM than this.
  • you should have a nightly backup (rsync is a good tool for this) from your SSD drive to another hard drive. Uncomfortably often when an SSD fails, it fails catastrophically (no data recovery at all)
• SSD RAID0 (data striping with no redundancy)
  • 4x 1TB SSD drives will cost ~$2000 (early 2014)
  • configured as a RAID0 (data striping with no redundancy) gives ~4TB usable space

  • can achieve speeds better than 1GB/sec ! (typical hard drives are ~120-150 MB/sec, ie - >8x faster)

  • Extremely useful when working with large tomograms or direct-detector movie mode data !
  • However, if any 1 drive fails, all data is lost, so these should be for active data processing only, and should have a nightly backup onto a traditional 4TB drive (rsync again).

Regular spinning hard drives: Note that you can also get ~1GB/sec performance out of spinning drives if you get a large enough RAID array. For example if you get an 8 drive RAID and put high speed regular hard drives in it, and have a high speed interconnect (NOT SAN), you can get pretty good performance.

A note on GPU computing: EMAN2 does have support for GPUs available, however, there are many caveats:

• You have to compile EMAN2 from source to get this capability (we haven't come up with a strategy for distributing usable GPU binaries due to library versioning issues)
• The only application where the GPU provides enough speedup to be worthwhile in EMAN2 is single particle tomography. For regular single particle analysis, most modern CPUs (with multiple cores) can outpace a GPU.
• If you do decide to try GPUs on a workstation, A: make sure you get Nvidia, we only support CUDA. B: don't waste your money on Tesla cards, just buy a high-end consumer gaming card. Performance will be nearly the same at ~1/10 the cost.

Suggestion as of 3/20/2012

Sandy - bridge Xeons are now available, and I've been getting questions about which computer to get again. Note that Macs are still using the earlier Westmere technology. Anyway, here's a quick analysis:

Sandy-bridge Xeons (E5-2600 series) have finally become available, but aren't available in Macs yet. Certainly the Mac Pro loaded with 12 cores will give you the best available performance on a Mac right now. However, it is very far from the most cost-effective solution. So, it really depends on your budget and goals. Westmere still offers a decent price-performance ratio if you want dual CPUs. If you are happy with a single CPU, I'd say Core-i5's are actually the way to go (this is what I just set up in my home PC).

Here is a rough comparison of 3 machines I use: Linux - 12 core Xeon X5675 (3.07 Ghz, westmere): Speedtest = 4100/core -> ~50,000 total (2 CPU ~$2880 total) Mac - 12 core Xeon (2.66 Ghz): Speedtest = 3000 -> ~36,000 total Linux - 4 core i5-2500 (3.3 Ghz+turbo): Speedtest = 6400 (turbo), 5600 (sustained) -> ~22,000 total (1 CPU ~$210)

Now, they have just released the Sandy-bridge Xeons, but, for example, a dual 8 core system: 16 core E5-2690 (2.9 Ghz): Speedtest (Estimated) = 5650 (turbo), 4950 (sustained) -> ~80,000 total (2 CPU ~$4050)

Now, the costs I gave above are just for the CPUs. If you wanted to build, for example, several of the core i5 systems and use them in parallel, you'd need motherboard, case, memory, etc for them as well. A barebones Core I5 pc with 8 GB of ram and a 2TB drive would run you ~$650.

If you built a 16 core system around the E5-2690, $4050 - CPU $600 - motherboard $200 - case $150 - power supply $300 - 32 gb ram $500 - 4x 2TB drives (equivalent)

So ~$5800 for the (almost) equivalent 16 core machine vs $2600 for 4 of the 4-core i5 systems.

ie - you pay ~2x for the privilege of having it all integrated into a single box. Of course, that buys you a bit of flexibility as well, and saves you a lot of effort in configuration and running in parallel, etc. It also gives you 32 GB of ram on one machine, which can be useful for dealing with large volume data, visualization, etc.

On the Mac side, a 12-core 2.93 Ghz westmere system with 2 GB/core of ram -> $8000 and would give a speedtest score of ~45,000. ie ~40% more expensive and 1/2 the speed of a single linux box with the 16 core config, and 3x as expensive and 1/2 the speed of the core-i5 solution.

Please keep in mind that this is just a quick estimate, and that actual prices can vary considerably, but as you can see, the decision you make will depend a lot on your goals and your budget.

Suggestion as of 12/1/2011

Obviously for large jobs you're going to need access to a linux cluster, but regardless you will still need a desktop workstation.

A complete answer to the question depends a bit upon your budgetary constraints, or lack thereof. As you are probably aware, at the 'high end', computers become rapidly more expensive for marginal gains in performance. Generally speaking, we tend to build our own Linux boxes in-house rather than purchasing prebuilt ones, both as a cost-saving measure, and to insure future upgradability. Then again, there is nothing wrong with most available commercial pre-build PCs as long as you get the correct components. For a minimal cost-effective workstation, I would suggest:

• Sandy-bridge series processor, the quad core Core i7-2600K is a good choice
  • If you can get one of the new 6-core versions, that would be 50% more performance
  • note that Sandy-bridge significantly outperforms the previous generation, so going with a 6-core from the pre-sandy bridge series is not a great choice)
  • If you can afford a dual processor configuration, with dual 6-core Xeon's you will presently have to go with the previous generation, as the Sandy Bridge Xeons won't be out for a while. This configuration (12 cores last gen) is worthwhile, but expensive.
• RAM - 3-6 GB/core is what I'd recommend for image processing
  • This depends a bit on the target application. For large viruses, you may wish to get more RAM/core
  • The performance benefit of high-speed RAM is rarely worth the cost. Get the fastest you can without breaking the bank
• Disk - we would generally get something like 4, 2 TB drives for data/user files configured as software RAID 5, with a small (~100gb) SSD as a boot drive, current Intel SSDs are good for this purpose.
  • Note that other than the very fastest SSD drives, none of the drives can actually keep up with the latest SATA busses anyway, so going out of your way to get the superfast SATA drive is kind of pointless

• Video - Get an NVIDIA card, NOT ATI, particularly if you plan on doing stereo. This will also get you some CUDA capabilities. A reasonably high-end GeForce with a good amount of RAM is generally fine with some caveats below.

• Stereo - This is a tricky and complicated issue. There are 2 main choices:
  • Active stereo
    • Requires a 120 hz stereo capable 1080P display, AND, importantly, a Quadro series Nvidia graphics card (to do stereo in a window under Linux !). Note that you will have difficulties making most consumer '3D TVs' work with this setup, though some will. The most reliable option is to get a monitor designed for stereo use with Nvidia cards (Acer makes a decent 24"). Note that this also requires a dual-link DVI port.
  • Passive
    • By FAR the easiest and cheapest option, which also allows multiple users with cheap passive glasses. It also does NOT require an expensive Quadro video card. Chimera and many other programs have built-in support for 'interleaved' stereo, which they implement without support from the underlying Nvidia driver, so you can do it even with cheap graphics cards. Only disadvantage is that you lose 50% of your vertical resolution. Personally this doesn't bother me overly. The other minor issue is that over the last couple of years these have been hard to find. Finally, LG came out with one which can be easily purchased again, though I confess we haven't purchased one of these new ones yet. Does not require dual-link DVI.
• Monitor - Dual monitor setups can be very useful for image processing. If you can afford it, I would suggest a high-resolution 30" primary display with a passive stereo secondary display. If you get an active stereo secondary display, you will need 2 dual-link DVI outputs on your graphics card.

hope that helps.

Note that these are just my own personal opinion, and do not represent an official recommendation from anyone other than myself. Your mileage may vary.